Hyundai Elantra MD/UD: Replacement - Rear Door. Repair procedures - Exterior - Body (Interior and Exterior) - Hyundai Elantra MD 2010-2015 Service manualHyundai Elantra MD/UD: Replacement

Door Trim Replacement
•
Be careful not to scratch the door trim and other parts.
•
Put on gloves to protect your hands.
1.
Using a screwdriver or remover, remove te rear door delta inner cover (A).
2.
After loosening the mounting screws, then remove the rear door trim (A).
3.
Disconnect the inside handle cage (A).
4.
Disconnect the connectors (A).
5.
Installation is the reverse of removal.
•
Make sure connectors are connected properly and each rod is connected securely.
•
Make sure the door locks/unlocks and opens/closes properly.
•
Replace any damaged clips.
Inside Handle Replacement
1.
Remove the rear door trim.
2.
After loosening the mounting screws, then remove the inside handle (A).

3.
Installation is the reverse of removal.
•
Make sure the door locks/unlocks and opens/closes properly.
•
Replace any damaged clips.
Door Latch Replacement
1.
Remove the following items :
A.
Rear door trim
B.
Window glass
C.
Outside handle
2.
Loosen the mounting bolt (A).
3.
Disconnect the rear door main connector (A).
4.
After loosening the door module mounting bolts, then remove the rear door module (A).
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0lb-ft)

5.
Disconnect the connector (B).
6.
Remove the rear door latch assembly (A).
7.
Installation is the reverse of removal.
•
Make sure the connector is connected properly.
•
Make sure the door locks/unlocks and opens/closes properly.
•
Replace any damaged clips.
Glass Replacement
1.
Remove the rear door trim.
2.
Remove the rear door belt inside weatherstrip (A).
3.
After loosening the mounting screws, then remove the rear door belt outside weatherstrip (A).
4.
After loosening the mounting screws, then remove the rear door delta molding (A).
5.
After loosening the mounting bolts and nut, then remove the rear door div channel (A).
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

6.
Remove the glass mounting hole plug (B).
•
Use the door switch to align the mounting hole/bolt with the hole in the door.
•
If unable to operate the window motor, remove the motor and align the hole by hand.
•
Be careful not to drop the glass and/or scratch the glass surface.
7.
Carefully move the glass (A) until you can see the bolts, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Tightening torque:
3.9 ~ 2.9 N.m (0.4 ~ 1.2 kgf.m, 11.8 ~ 8.7 lb-ft)

8.
Installation is the reverse of removal.
•
Roll the glass up and down to see if it moves freely without binding.
•
Adjust the glass position as needed.
Speaker Replacement
1.
Remove the rear door trim.
2.
Disconnect the speaker connector (A).
3.
After loosening the mounting screws, then remove the speaker (B).
4.
Installation is the reverse of removal.
•
Use sheet metal screws to secure the speaker.
•
Make sure connectors are plugged in properly.
•
Make sure the door locks/unlocks and opens/closes properly.
•
Replace any damaged clips.
Power Window Motor Replacement
1.
Remove the rear door trim.
2.
Disconnect the power window motor connector (A).
3.
After loosening the mounting screws, then remove the power window motor (B).
4.
Installation is the reverse of removal.
•
Grease should be applied to areas where there is rotational parts and springs.
•
Roll the glass up and down to see if it moves freely without binding.
Outside Handle Replacement
1.
Remove the rear door trim.
2.
Remove the hole plug (B).
3.
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque:
0.7 ~ 0.5 N.m (0.07 ~ 0.1 kgf.m, 1.0 ~ 0.7 lb-ft)

4.
Remove the outside handle (A) by sliding it rearward.
5.
Installation is the reverse of removal.
•
Make sure the door locks/unlocks and opens/closes properly.
Door Module Replacement
1.
Remove the following parts:
A.
Rear door trim
B.
Window glass
C.
Outside handle
2.
Loosen the mounting bolt (A).
3.
After loosening the mounting bolts and nut, then remove the rear div channel (A).
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

4.
Disconnect the rear door main connector (A).
5.
After loosening the rear door module mounting bolts, then remove the rear door module (A).
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

6.
Disconnect the connectors, then remove the wiring harness (A).
7.
Installation is the reverse of removal.
•
The area of whole parts should be applied with sufficient grease.
•
Make sure connectors are connected properly and each rod is connected securely.
•
Make sure the door locks/unlocks and opens/closes properly.
Door Side weatherstrip Replacement
1.
Detach the clips, then remove the rear door side weatherstrip (A).
2.
Installation is the reverse of removal.
•
Replace any damaged clips.

Adjustment
Glass Adjustment • Check the glass run channel for damage or deterioration, and replace ...